Windows Update Error Code 80246007: Get All The Resolving Methods Here And Now

In the current scenario, there have been a number of Windows Update error codes, which may be impossible to count. This long list of error codes can easily be found in the post published by Microsoft. Among them, the Windows Update error code 80246007 is the most common error code that the users have faced till now.

This Windows error code can be seen when you are updating Windows. When you are trying to update your Windows Operating System, the following error message shows up: “Windows has stopped this device because it has reported problems. (Error Code 0x80246007).

So, if you are currently encountering this irritating issue, then you can try to follow this article. Hence, in this article, you will get to know the cause and the solutions to fix the issue. Therefore, as soon as possible, proceed to the following part of the article.

Know the Common Causes that Influences the Windows Update Error Code 80246007

Therefore, here in this section, you will be getting the causes of this issue. Hence, you can now follow the points that are listed as follows:

1. In case, the internet connection is not working properly, then the issue can occur.
2. Corrupted Windows system files can also restrict the Windows update.
3. In another case, if the third-party antivirus conflicts with the Windows Update process then also the issue can occur.
4. Too many junk files in the system’s hard drive can also be a reason for the issue to occur.
5. A recent virus or malware attack to the system can also lead to this Windows update problem.

Hence, these are some of the common causes for the problem to occur. However, there can be more such causes that can be responsible for the issue to occur. Therefore, after knowing the causes, you can proceed to the next part of the article below.

Methods that will Troubleshoot the Windows Update Failed Error Code 80246007 Without A Doubt

In the solution part of the article, we will teach you the methods to fix the Windows error code. Also, remember to perform all the given steps without missing any. Hence, you can now have a look at the methods that are discussed as follows:

Method 1: Try to Disable the Security Software of your System (Temporarily)

Disabling the inbuilt Security Software of your system helps to resolve this Windows problem easily. For Windows, the inbuilt Security software is Windows Defender Security Center that protects your system. However, if you do not know the steps to disable the security software. then follow the steps that follow:

• In the first step, open the Windows Defender from the Start menu. By using the search bar of the Start menu find and open the Windows Defender.
• As the Windows Defender Security Center window opens, click on the shield icon under the home button.
• Now, open the Virus & threat protection settings section and then turn off Real-time protection option and Cloud-based protection option.
• After that, navigate to the browser icon and then turn off the Check apps and files option.
• Also, you can turn off the SmartScreen For Windows Store apps option.
• Once done, close the Windows Defender Security Center window and then, check for the issue if it occurs or not.

Therefore, this is how you can fix the issue by disabling the Windows Defender. However, in case the issue does not resolve, then have a look at the following method.

Method 2: Temporarily turn off the Windows Firewall system

In another method, you can try to turn off the Windows Firewall in order to fix the issue. Hence, the steps that will help you to get through the process are as follows:

• From the Start menu, search and open the Control Panel. 
• As the Control Panel window opens, set the View By option to Small Icons. Now, locate the Windows Firewall option from the list.
• After that, click on it and then, select the Turn Windows Firewall on or off option. This option will be available on the left pane of the window.
• In the next step, click on the radio button beside the Turn off Windows Firewall (not recommended) option. Here you have to perform this step both for the Private and Public network settings section.
• Finally, click on the OK button in order to save the changes.
• Now, check if the Windows error code still persists or not.

Hence, turn off the Windows Firewall will ensure that you can fix the issue on your own. However, if the issue still troubles you, then follow the next part of the article below.

Method 3: Run the Windows Update Troubleshooter Tool

The Windows Operating System comes in with the inbuilt Troubleshooter tool. This troubleshooter tool helps the users to identify and resolve some of the major and minor issues. Therefore, you should also use this tool in order to fix the Windows update error code on your own. So, the steps that you can follow are stated below:

• From the Start menu, try to open the Windows Troubleshooter toll. For this, type Troubleshoot in the search bar and then, select the Troubleshooter option from the results.
• As the Windows Troubleshooter window opens, proceed to the Windows Update section.
• On arriving at the Windows Update section, click on it. After that, click on the Run the Troubleshooter button.
• Now, allow the Windows Troubleshooter tool to find and fix the Windows update error code.
• Once the process finishes, reboot your system.
• As the system reboots, you can now check if the Windows issue is resolved or not.

Hence, by following the steps given above you will be able to fix the issue on your own. In case you want to know more fixing methods, you can proceed to the next section.

Method 4: Reset Windows Update Components Manually

This is the most complex but effective solution that can easily eliminate the Windows error code. Therefore, you have to follow all the steps with full attention. Any wrong step can make things even more complex. Hence, try to follow the steps that we have listed down for you:

• Press the Windows logo key to open up the Start menu. Now, type “cmd” in the search bar.
• After that, right-click on the Command Prompt option and click on the Run as Administrator option.
• As the black Command Prompt window opens, enter the following commands:
  • First Command is: net stop bits
  • Second Command is: net stop wuauserv
  • Third Command is: net stop appidsvc
  • Fourth Command is: net stop cryptsvc
• Also, remember to press the Enter key after each command.

• Once the above commands execute enter the next set of commands:
  • Ren %systemroot%\SoftwareDistribution SoftwareDistribution.old
  • Ren %systemroot%\system32\catroot2 catroot2.old
• Here, also you have to hit the Enter key after typing in each command.

• Again, enter the following commands when the previous commands execute:
  • First Command is: net start bits
  • Second Command is: net start wuauserv
  • Third Command is: net start appidsvc
  • Fourth Command is: net start cryptsvc
• Here also, you have to hit the Enter key after every command.
• Finally, close the Command Prompt window and then reboot your system.
• Once the system reboots, check for the Windows error code problem if it still persists or not.

So, this is how you can reset the Windows Update Components manually, allowing you to fix the issue in no time. For other resolving methods proceed to the next part of the article below.

Method 5: Fix Windows Registry of the system

Fixing the Windows Registry files will help to resolve the Windows update issue. Hence, the steps that you can perform are as follows:

• At first, you have to log in as the Administrator on your system. Now press the Windows key and the “R” key at the same time.
• As the run box opens, type regedit and then hit the Enter key.
• Once the Windows Registry window opens, follow the path: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\BackupRestore\
• On arriving at the folder, find the FilesNotToBackup key. Reset the key and then, close the Windows Registry Editor window.
• Finally, check if you can update the Windows Operating System or not.

For the last resolution, you can have a look at the next section below.

Method 6: Check the DISM and System files

In case your Image service or system files are corrupt then you can get the Windows update problem. Therefore, you have to check them through the steps that are given below:

• Open the Command Prompt as an administrator from the Start menu.
• As the Command Prompt window opens, type the command: DISM /Online /Cleanup-Image /RestoreHealth
• Press the Enter key after typing the command.
• As the command executes, enter another command: sfc /scannow
• Here also you have to hit the Enter key.
• Once the command executes, close the Command Prompt and check for the issue.

Hopefully, now you will be able to resolve the Windows Update issue instantly.

Endnotes

So, this is how you can fix the Windows Update error code 80246007 by carrying out our best methods. Hence, we expect that you can resolve the issue without facing any difficulty. However, if you get to encounter any issue then our experts are there for you. Hence, you can get back to us through the comments section below.